USB Plug for Nextbase Dash Cam (25 Viewers)

[MichaelT]

Looking to wire my nextbase dash cam in. I've installed a USB socket for the SAT nav so thought I'd plug in there rather than direct to a piggy back fuse.

Currently it has a cigarette plug on so thought I'd try just changing to a USB plug so looking for one I can wire myself.

 

[U.Toadifact]

If you read the installation instructions carefully you should see that Nextbase do not recommend using a usb socket for power. I think it is because 12v is needed as opposed to the 5v available at a usb feed.

 

[pappajohn]

Just buy a USB to USB lead.
Wiring a USB plug in place of a cig lighter plug will be near on impossible.

Just read the post above.
Cut the plug off and wire to a 12v supply.

 

[yorkiebar]

If you read the installation instructions carefully you should see that Nextbase do not recommend using a usb socket for power. I think it is because 12v is needed as opposed to the 5v available at a usb feed.

Every dashcam I've seen has a 5v usb power input

 

[ramsthom]

Run my Nextbase in the car off a usb connection.

^{_{Subscribers  do not see these advertisements}}

 

[Cal54]

I’ve just purchased a Nextbase dash cam and have also ordered the hardwire kit. I know nothing about the power gubbins so will be getting a professional to wire it in. Don’t want to use the cig socket as the sat nag uses that and I don’t want to have a bulky double adapter.

 

[Gellyneck]

Be aware different usb output sockets can supply different amperage outputs so you'll need to take this into consideration. Does the socket provide sufficient?

 

[daveclare]

I used one is these kits from evilbay. Still working fine three years later with the nextbase. The difficult bit was threading the wire through to the screen area, from the fuses under the steering wheel. But it didn't take long to fit.

 

[MichaelT]

Be aware different usb output sockets can supply different amperage outputs so you'll need to take this into consideration. Does the socket provide sufficient?

It's on a 5a fuse, I looked at the hardwire kit and that had 2a I think.

 

[CAB96]

It's on a 5a fuse, I looked at the hardwire kit and that had 2a I think.

Yes, but USB is 5v, not 12v, so needs higher amps for the same power.

It may be fine, have you tried it on USB?

My Garmin satnav has a dashcam built in, USB will run the sat nav but there's not enough power to run the camera.

^{_{Subscribers  do not see these advertisements}}

 

[Gellyneck]

It's on a 5a fuse, I looked at the hardwire kit and that had 2a I think.

But the amperage output is determined by the USB socket with them ranging from somewhere around 1A to 3.2A. If it's one of the lower output ones it may not deliver enough to run the dashcam.

 

[MichaelT]

Yes, but USB is 5v, not 12v, so needs higher amps for the same power.

It may be fine, have you tried it on USB?

My Garmin satnav has a dashcam built in, USB will run the sat nav but there's not enough power to run the camera.

Haven't tried it as I was look8ng for suggestions of a suitable wireable USB plug.

 

[MichaelT]

But the amperage output is determined by the USB socket with them ranging from somewhere around 1A to 3.2A. If it's one of the lower output ones it may not deliver enough to run the dashcam.

It's 4.2a but I'm using one socket for the sat nag

 

[BusyBuilder]

I used same ebay hard wire set, and yes it took longer taking the dash apart to thread the wires through to fuse box by driver. Took me a bit to find the right fuse that was ignition switched but gotthere in the end with piggyback fuse.

 

[Gellyneck]

It's 4.2a but I'm using one socket for the sat nag

If it's a total of 4.2A (it will be if it's fused at 5A) with two outputs sometimes they're split 2.1A and 2.1A but others are are 3.1A and 1.1A.

^{_{Subscribers  do not see these advertisements}}