Rapido oven models

wigster said:
Cant find any numbers on oven itself , will dig through paperwork that come with van.
No, light and rotisserie not worth it mate :)
Click to expand...
So the Magnum one at £358.95 delivered is the better option?
 
I would say so .

If you cant find any installation instructions anywhere ive got the small book that came with oven , its not very detailed but has some drawings in it on installation. Let me know if you need it (y)
 
Last edited:
the oven side walls get hot so bear this in mind when making the hole
from memory mine sits on an internal shelf, which might be alu lined and the outer ovenframe keeps the wood away and allows air flow, they do kick out a lot of heat from the top louvre so plan the area above the appliance, i like the black louvre [ @wigster ] above as the cabinet does warm up.
Are there any regs for fitting ovens?
 
Mine will fit directly where the centre drawer is. I don't envisage any issues as it is already built to accept a drawer or an oven (first owner chose no oven option). The top behind the hob is already vented on mine so it can vent from the front and the top.

EDIT
Purchase made (y) thanks @wigster
 
Glad to help (y)

Subscribers  do not see these advertisements

 
Back to the drawing board
On inspection today I don't have the width require for the SMEV
Magnums have been kind enough to fully refund me as it is sat waiting for courier.
Best I can accommodate is 460 ish so tape measures out please :)
 
ouch
just measured my smev and it needs 495 ish, so guessing that might be smevs standard ...500mm

good luck :)
 
Last edited:
I can see from @Scattycat picture that I will have to remove the top cutlery drawer. The oven must be higher than the boxing out of the boiler to fit
I'll then have to refashion below the oven
image.jpeg
 
As Magnums were so good I've re ordered from them (y)
The bonus I suppose beside £100 less is it's 6 litres more volume despite being narrower

Subscribers  do not see these advertisements

 
Are Rapido still doing that as a full length drawer front or is it a door?
image-jpeg.109615
 
Techno said:
Are Rapido still doing that as a full length drawer front or is it a door?
image-jpeg.109615
Click to expand...
It's a door with a deep upper drawer inside. Off to get the details and measurements of the oven for you
Chris
 
Techno said:
I can see from @Scattycat picture that I will have to remove the top cutlery drawer. The oven must be higher than the boxing out of the boiler to fit
I'll then have to refashion below the oven
View attachment 109828
Click to expand...

May be not, because we have a cutlery draw below the oven. l'll measure it out later for you.
. . . . . . . . . . . . 10 minutes later . . . . . . . . . . . .
The oven is about 18"(46cm) deep. Sorry I can't be more accurate without taking the oven out., but that figure includes the shelf it sits on.
Hope that is of some help
 
Last edited:
Presumably your cutlery drawer is narrower than the drawer front?
 
Back again. I have an instruction manual for every pice of equipment in the MoHo except the oven. I cannot find the model number on it either. The cut aperture measures 44 across no lip included and 45.5 high which includes the lips.
The picture is a bit dark but it shows the drawer open with a bottle rack underneath
Hope info is useful
Chris

Subscribers  do not see these advertisements

 

Attachments

  • image.jpeg
    image.jpeg
    64.7 KB · Views: 59
This is mine same as the one you saw on eBay magnums grimsby I think.I have a vent on outside bloody draft in high winds
 

Attachments

  • 1465327871968-1285210176.jpg
    1465327871968-1285210176.jpg
    110.2 KB · Views: 51
  • 1465327968833736121628.jpg
    1465327968833736121628.jpg
    73.3 KB · Views: 46
  • 14653280123632063549478.jpg
    14653280123632063549478.jpg
    56.8 KB · Views: 45
I won't need an outside vent
It's vented on the front and......

image.jpeg
 
I'll see how it goes Mike. You know I'm not afraid of holes :LOL:
If the oven instructions call for it I will (y)
I think I can make a decent job of remanufacturing the top drawer to fit below. All the wood is there to do it. Especially as I'll have a whole centre drawer surplus
 
Last edited:
I have a suspicion that the vent in the outside wall which is not used on ALL vans is installed more to give access where difficult to the gas and electrical connection at the rear.
If the instructions don't beg for one I will find a way to do it without creating another draft.
 
Next winter..

Andy's For Sale Advert

Gas Oven Grill,.. one very careful owner.. only used twice..

Selling as I need more payload for batteries.. :LOL:
 
First glimpse
image.jpeg

New small drawer insert from Magnums
image.jpeg

Drawer runners moved down
image.jpeg

Enlarged opening to three sides with multitool
image.jpeg

image.jpeg

image.jpeg

image.jpeg

Just got to pipe the gas up and resize the top drawer carcass to fit here
image.jpg

Subscribers  do not see these advertisements

 

Attachments

  • image.jpeg
    image.jpeg
    113.2 KB · Views: 35
Last edited:
No outside vent , not called for in instructions.
Cut some wood out to facilitate connection with under sink wood work removed.
Used some water hose to add protection to gas pipe
I previously used the vacant oven connection on the manifold for the outside BBQ so T'd in to this rather than T off the hob. The manifold is fed in 10mm copper. All the outgoings are 8mm each.
image.jpeg
image.jpeg
image.jpeg

Drawer is now remodelled ready to fit
 
Last edited:
I know it's champagne night but been there done that :D

Drawer resizledded hic
image.jpeg
 
Now having lost quite a big drawer lies the task of reinventing a place for everything
image.jpeg
image.jpeg
image.jpeg
image.jpeg

Subscribers  do not see these advertisements

 

Join us or log in to post a reply.

To join in you must be a member of MotorhomeFun

Join MotorhomeFun

Join us, it quick and easy!

Join us

Log in

Already a member? Log in here.

Latest journal entries

Back
Top