Poor quality crimping ? (61 Viewers)

[ianto999]

Not having much luck atm.
Asked a mobile ‘specialist’ (lots of +ve reviews on FB, which are real) to do some additions to electrics.
Had a look properly today and saw this..
I’ve only dabbled with crimping before but this looks poor to me.
I’m learning to always check carefully what people have done before they leave…
View attachment 954006

 

[ianto999]

 

[Manic]

He obviously forgot his crimping tool and just used his pliers

 

[Two on Tour]

View attachment 954018

Was the guy that did that wearing a six gun and a Stetson ?

............. and that's why I do those jobs myself.

 

[St3v3]

Pull on the wires and see what happens...

You probably should get him back.

^{_{Subscribers  do not see these advertisements}}

 

[Vaman]

Blue red yellow, ratchet crimping tools are very reasonable on ebay. Re do the whole lot, as they are they will current limit & oxidise and give you grief in all sorts of weird ways.

 

[Lenny HB]

Also the crimps look like cheap & nasty ones, I'd want them replaced.
All of them just on the battery terminal is a bodge and very close to the metal seat frame.

 

[ivorantony]

Buy a hydraulic crimping tool with properly sized terminals for your wire size with again sized heat shrink and do the job yourself, it would still work out cheaper then getting someone in,

 

[bigtwin]

That looks to be a really shoddy job. It may be the angle that the photo has been taken from but that seriously looks as though it needs a protective insulating boot over the battery post. However, with all those crimp connections on there that could be a challenge.

I would not be happy with that job.

Ian

 

[gus-lopez]

That's frightening that close to the seat Base.

^{_{Subscribers  do not see these advertisements}}

 

[eurajohn]

That's frightening that close to the seat Base.

Ducato has a thick plastic sheet between the seat base and the mounting,

 

[Lenny HB]

Ducato has a thick plastic sheet between the seat base and the mounting,

Must depend on the seats and the converter, I've be er seen one.

 

[ChrisL]

That is really amateur job, I wouldn't call him back, i'd send him that photo and ask for your money back. I don't know where you are but if you can get to them i'd ask Offgrid Power Solutions to do the job properly for you and if there's space fit a positive bus bar. They are very helpful and it shouldn't be much work perhaps pm RogerIvy and ask.

 

[Ditcha]

View attachment 954018

That looks like one of my jobs

 

[PlacidoD]

"That looks like one of my jobs "

The battery seems appropriately named!!

^{_{Subscribers  do not see these advertisements}}

 

[BouncyBoatFolk]

This is the best picture I have on file,it shows the plastic cover removed and put to one side in the passengers foot space.The plate sits immediately above the battery,thus insulating the seat base. This plate in no way excuses the shoddy cable work shown in the O.P.s original photo.
Obviously, the O.P. would need to remove the seat again to achieve a more reliable and professional finished job.
Mike.

 

[Guigsy]

Even my DIY electrics are better than that. I bet they wouldn't survive a yank test. And I agree with others, I'd be very itchy about that positive terminal being that close to metalwork. Go over a big bump, arrive at the destination and wonder why your electrics don't work.

 

[EuroTrotters]

Was the guy that did that wearing a six gun and a Stetson ?

............. and that's why I do those jobs myself.

Me too

 

[gus-lopez]

Go over a big bump, arrive at the destination and wonder why your electrics don't work.

That's if it doesn't arc,short out ,set fire to the seat you're sitting on........

 

[Richard n Ann]

Looks like the job I would have done when I was 13 with no money and using my dad's old pliers. Just needs some tape round it now

^{_{Subscribers  do not see these advertisements}}